Simple 3D model of a tray

  • Statusi: Closed
  • Çmimi: $20
  • Kandidaturat e marra: 31
  • Fituesi: VKarmaa

Përmbledhja e konkursit

Hello-
I'm looking for a simple 3D model of a tray built from the attached rough drawings. Please review the attached PDF - it has the necessary dimensions and details. Some notes below:

1) The tray should be 11" long x 3 1/4" wide
2) The thickness of the tray and all the walls should be 2.5MM thick
3) There should be 3 channels in the bottom of the tray (created by 2 walls along the bottom of the tray
4) The tray should be 2" high
5) The front of the tray is open (no front wall)
6) All corners of the tray should have a slight rounding (no sharp corners)
7) The pattern of the tray throughout (walls, floor, etc.) should be small honeycomb (not solid walls). Example: https://cl.ly/90df93d132d3
8) The final file needs to be a 3d printable file, and it will need to be in 2 parts (6" long max). The 2 parts will need to snap together easily to form 1 full piece.

THANK YOU in advance

Aftësi të rekomanduara

Vlerёsimi i punёdhёnёsit

“Navodit was highly skilled and fast with revisions. It felt like we had a great partnership to get the project completed. Looking forward to working with him again in the future!”

Fotoja e profilit charlstonsmallsc, United States.

Punimet mё tё mira nga ky konkurs

Shiko mё shumё vepra

Këndi publik i sqarimeve

  • charlstonsmallsc
    Krijuesi i Konkursit
    • 4 vite më parë

    I want to sincerely thank all of you for your entries on this project. You all submitted amazing work - it was a very difficult decision to narrow to just one design. Thank you all very much!

    • 4 vite më parë
  • khurrummah85
    khurrummah85
    • 4 vite më parë

    Can you tell the 3D Printer type because the design of the tray depends upon the technique of Printing. Is it FDM, SLS, SLA ? Because some designs need support structures too but some don't

    • 4 vite më parë
    1. tejaspetkar2
      tejaspetkar2
      • 4 vite më parë

      SLA,

      • 4 vite më parë
  • ahmedkasse
    ahmedkasse
    • 4 vite më parë

    hi sir i'm working on the tray and i jyst want to know where you want the tray to sepreate and join

    • 4 vite më parë
    1. charlstonsmallsc
      Krijuesi i Konkursit
      • 4 vite më parë

      Length-wise. I can only print 6", so by cutting the 11" length in half, that will work. Hope that makes sense.

      • 4 vite më parë
  • mahipalbasera3
    mahipalbasera3
    • 4 vite më parë

    #24

    • 4 vite më parë
  • charlstonsmallsc
    Krijuesi i Konkursit
    • 4 vite më parë

    Thank you all for your submissions so far. Just to explain my star rating:
    3 stars = good
    4 stars = very good

    Every submission is appreciated so far!

    • 4 vite më parë
  • DC47
    DC47
    • 4 vite më parë

    Dont Close the contest Early.

    • 4 vite më parë
  • jaypang
    jaypang
    • 4 vite më parë

    Could you elaborate on "channel wall is sloped at the front" please? It's the only part of your sketch which is slightly ambiguous. Thanks

    • 4 vite më parë
  • VKarmaa
    VKarmaa
    • 4 vite më parë

    working on it. If possible please #increaseprize

    • 4 vite më parë
    1. VKarmaa
      VKarmaa
      • 4 vite më parë

      Also, please tell the purpose/use of the tray

      • 4 vite më parë

Shfaq më shumë komente

Si të fillosh me konkurset

  • Posto konkursin

    Posto konkursin Shpejt dhe thjeshtë

  • Merr shumë propozime

    Merr shumë propozime Nga e gjithë bota

  • Zgjidh kandidaturën më të mirë

    Zgjidh kandidaturën më të mirë Shkarko dokumentet - E thjeshtë!

Postoni një konkurs tani! ose bashkohu me ne sot!