Përpunimi i sinjaleve Jobs

I need a custom-designed PCB for home automation applications, built around the ESP32 DevKit V1. The PCB will control: - AC loads via Omron G5LE SPDT relays, optocouplers, and BJT drivers. - AC dimming (lamp/fan) using MOC3020 opto-driver + BTA16 TRIAC. - DC loads (like RGB LED strips) using IRF540N MOSFETs. Key features: - Integrated AC-DC power supply with bridge rectifier, dual 7805 regulators, and ESP32 3.3V regulator. - Optical isolation between ESP32 logic and high-voltage circuits. - External KF301 series connectors for AC input, AC load output, and 12V RGB outputs. - Status LEDs for debugging and system monitoring. Requirements: - Compact and small form factor - Standard KF301 series connectors - Improvement related safety - Songle high Power 30a relay replacement - 240ac to ...

Project Title: > High-Speed Dual-Node RF Relay (125kHz / 2.4GHz / 315MHz) - Teensy 4.1 > Project Description: > I am looking for an experienced RF/Embedded Systems Engineer to design a 100% workable dual-node relay system for a keyless entry project. > The System Architecture: > * Node A (Car-Side): Must sense a 125kHz LF wake-up signal (AS3933 + ANT-125K) and relay data via 2.4GHz (NRF24L01+ PA/LNA). > * Node B (Key-Side): Receives 2.4GHz, re-transmits 125kHz (TC4420 driver + LC tank), and listens for 312/314/315MHz UHF response (CC1101) to relay back to Node A. > * Hardware: Both nodes are based on the Teensy 4.1. > Key Technical Requirements: > * PCB Design: 4-layer board preferred for EMI shielding. Must include proper ground planes and keep-out zo...

I have an Angular front-end that now needs secure Single Sign-On through Auth0. The only identity provider I want wired up at this stage is Google, and I only need to pull the user’s basic profile information once authentication succeeds. Here is what I’m expecting from you: • Configure Auth0 and my Angular project so a user can click “Sign in with Google,” be redirected to Google, grant consent, and land back in the app already authenticated. • Expose the returned ID token and profile object inside an Angular service so the rest of the app can subscribe to authentication state. • Add a simple route guard that blocks protected routes when the user is not logged in. • Include a clean logout flow that clears the session both locally and in ...

I’m building an automated live-play poker table and need the complete RFID hardware blueprint that will let software read every chip on the felt in real time. The table will hold well over 100 tagged chips at once, and I want reliable High-Frequency (13.56 MHz) reads at a maximum distance of about 10 cm from the antennas under the layout. Your task is purely on the hardware side: define an architecture that can see each chip as stacks move, bets slide, and pots grow, then pass clean data to the software team through a simple API or wired interface of your choice. Key expectations • Robust HF antenna array layout sized for a poker table, including multiplexing strategy to handle >100 simultaneous tags without collisions or dead zones. • Reader, controller, and MCU/FPG...

Wir entwickeln ein Music Tech Produkt, das die komplette Signalkette von E Gitarre und Bass bis zum Lautsprecher in einem System abbilden soll. Das System vereint kabellose Übertragung, Echtzeit Audio Processing, ein App Interface für Presets und Steuerung sowie eine Plattform Perspektive, sodass Sounds und Setups reproduzierbar werden und später erweitert werden können. Unser Fokus liegt auf einem bühnen und tourtauglichen Workflow, der auch in realen und stark gestörten 2,4 GHz Umgebungen stabil funktioniert. Es existieren bereits Hardware Prototypen und mehrere Iterationen von Sender und Receiver, unter anderem auf Basis von STM32 und ESP32. Die Zusammenarbeit ist auf mindestens zwölf Monate ausgelegt. Für die Rolle gibt es die Möglichkeit, ...

Ju lutemi Regjistrohuni ose Identifikohuni për të parë të dhënat.

I own a set of industrial-grade fans and want a clear picture of their current condition as quickly as possible. The job centres on a single spectrum vibration analysis that will reveal any bearing, alignment or balance issues. From that data I expect a concise machine health report and a short-term monitoring plan I can follow month by month. Deliverables I need from you: • One FFT spectrum analysis file (raw and processed) • A written health report explaining detected faults, severity and recommended fixes • A template or brief guide for monthly condition-monitoring reviews I can perform myself You are free to use the vibration tools you prefer (e.g., VibXpert, Emerson CSI, SKF Microlog, MATLAB) as long as your output is compatible with common formats such as CSV...

We are developing a carwash kiosk control board that will work together with our Paymore TPOS device, and we are looking for an experienced embedded hardware designer to design a production-ready PCB. This is a real commercial product that will go into mass production, therefore the design must be industrial-grade and manufacturable. The board will control a P10 LED panel (HUB75) that runs continuously 24/7, displaying countdown timers and simple messages. The system must also include Pulse+ and Pulse− inputs that can operate either as dry contact inputs or opto-isolated inputs, counting pulses and triggering system actions. Based on the detected pulses, the board must activate one of 10 independent output channels that can drive 5V or 24V signals for a defined period and then autom...

I have a commerical infrared device I want to push beyond its stock limits by unlocking and fine-tuning the voltage-gating parameters, and explore any additional user-interface controls that govern current (U/I). My end-goal is better overall performance without compromising stability or safety. You will need to access an unknown programmer interface via a 6-pin connector, determine the language, locate the relevant developer-level menus etc, and apply changes. Experience with low-level hardware interfaces a must. Acceptance criteria: • Device boots and functions normally after modifications • Voltage and current settings report the new, target values • Device test and verification prior to final payment • Some minor hardware modifications may be necessary (pr...

I need five separate input-output matching networks for the MACOM CGHV270305, one for each of the following RF bands: • 30–200 MHz • 200–600 MHz • 600 MHz–1.8 GHz • 1.8GHz–4 GHz • 4GHz–6 GHz For every band the network must deliver at least 30 W across the full span while maintaining solid, stable gain. I will verify this from the final performance plots, so please present both power-output and gain data together in clear scatter-plot format. Alongside the simulation results I need production-ready DXF files of the matching PCB layouts. Keep the drawings aligned with recognised industry standards so they can move straight into fabrication without extra re-work. Deliverables 1. S-parameter models (touchstone) and any suppor...

PCB DESIGN with these or better components placement Processor & Memory Main SoC NXP iMX8M Plus — Quad Cortex-A53 1.8GHz + Cortex-M7 800MHz Safety MCU TI TMS570LS3137 — dual-core lockstep Cortex-R4F, SIL-2 certified Diag FPGA Lattice MachXO3LF-9400 — in-situ verification logic, <2ms latency RAM 4 GB LPDDR4, ECC enabled, 1600 MT/s Flash 32GB eMMC 5.1 (AES-256-XTS) + 128MB QSPI NOR boot Wireless MCU ESP32-S3 co-processor (Wi-Fi 6) Sensor Specifications Temperature PT1000 ±0.05°C (primary), DS18B20 ±0.5°C (backup), NTC (tertiary). Range: −40 to +150°C Humidity SHT45 ±1.0%RH + HDC3020 ±1.5%RH. Range: 0–100%RH, 0–85°C Pressure MS5837-02BA 0–2bar ±0.05%FS + MS5837-30BA 0–30bar (secondary) L...

Project Title: Miniature Piezo Preamp PCB (10mm) – Reverse Engineer & Redesign Project Overview I am developing a professional leak detection microphone used for plumbing diagnostics. The system uses a piezoelectric sensor to detect vibration and sound from water leaks inside pipes. I already have a working preamp circuit, but the PCB is too large for my application. I need an experienced electronics engineer to analyze the existing design and redesign it into a much smaller PCB. The new design must maintain similar electrical performance but reduce the physical size so it can be mounted directly on the piezo sensor and permanently sealed with epoxy resin inside a capsule. Primary Objectives 1. Analyze or replicate the functionality of my existing piezo preamp. 2. Redesign ...

I need a seasoned LUA developer who also speaks the language of audio engineering to extend the processing palette on Symetrix, RANE and Allen & Heath DSP platforms. The work sits squarely inside each manufacturer’s SDK, so the GUI framework is already included what we need from you is efficient signal-flow code that drops straight into the existing interface. Primary tasks • Write well-commented LUA modules for DSP • Add pitch and general frequency-management routines that can be chained with, or operate independently of, the above effects. • Optimise code and supply test files that we can provide feedback on Further details on request..

Description Of Project - HRID-AI is a low cost handheld device aimed at estimating ejection fraction using multimodal biosignals (ECG, seismocardiography, and cardiac acoustics). It uses a combination of biosensors to detect abnormalities in ECG, presence of abnormal heart sounds and their interpretation as well as usage of seismocardiographic signals to provide an estimate of Ejection Fraction. The principle has been verified through multiple studies done in reputed institutions The goal is rapid point-of-care triage for echo referral in emergency and low-resource settings in patients of Heart Failure with Reduced Ejection fraction We need your support, skills and expertise for sensor integration, embedded design, signal acquisition. Current Status- We have so far been able to dev...

We need an electronics engineer to implement a PCB design based on an existing schematic for a renewable energy monitoring project. The system measures electrical parameters from multiple sources including a solar panel, wind turbine, battery, and inverter output. The schematic already exists in PDF format and includes components such as Arduino Nano Every, MCP3903 ADC, ADS1115, WCS1600 current sensors, and HC-12 communication module. The task is mainly to follow the existing schematic, verify the design, and create a manufacturable PCB layout.

I am ready to move from concept to production on a 55-Zoll LCD Digital-Signage-Screen and need an experienced hardware developer to guide the full electronics side. The panel size is fixed at 55", and my preferred control solution is a Huidu motherboard, Android 13, 14; if you have a strong case for an equivalent European board, we can discuss it— The job covers everything between the raw panel and a turnkey prototype: selecting the exact Huidu mainboard model, designing or adapting the logic board, defining all I/O (HDMI, USB, Ethernet, Wi-Fi, audio, power input, service port), creating schematics and PCB layout, and supplying a production-ready BOM with component alternatives that are immediately sourceable in Europe. I will also need the firmware flashed, tested, and demonstr...

I need help turning three off-the-shelf modules now sitting in my glasses prototype—a USB 2.0 hub, a USB audio codec (mic plus stereo out) and a dual-channel Class-D amplifier—into one long, narrow board that can slide inside the temple arm. The space I have measured is roughly 80 mm × 15 mm, so the layout has to be linear rather than squarish, with components placed to keep the height profile as low as practical. The board will run exclusively from the host’s 5 V USB rail; no batteries or additional supplies are planned. Because this is for voice prompts and basic media playback, a standard-grade codec is fine—I’m not chasing audiophile specs, just dependable microphone input and clean stereo output that won’t hiss or pop when the amp is idle. A...

Description Of Project - HRID-AI is a low cost handheld device aimed at estimating ejection fraction using multimodal biosignals (ECG, seismocardiography, and cardiac acoustics). It uses a combination of biosensors to detect abnormalities in ECG, presence of abnormal heart sounds and their interpretation as well as usage of seismocardiographic signals to provide an estimate of Ejection Fraction. The principle has been verified through multiple studies done in reputed institutions The goal is rapid point-of-care triage for echo referral in emergency and low-resource settings in patients of Heart Failure with Reduced Ejection fraction We need your support, skills and expertise for sensor integration, embedded design, signal acquisition. Current Status- We have so far been able to dev...

I am looking for an embedded systems developer to write Arduino code to communicate with the MCP3903 energy measurement IC from Microchip using the SPI interface. The goal of the project is to read voltage measurements from three channels of the chip and output the values through the Arduino serial monitor. Hardware: Arduino board (Arduino Uno or compatible) MCP3903 analog front-end IC SPI communication Requirements: The code should: Initialize SPI communication between Arduino and the MCP3903. Configure the MCP3903 registers correctly for basic operation. Read measurement data from the following channels: CH0 CH1 CH2 Convert the raw ADC data into readable voltage values (or at least raw measurement values). Print the measured values continuously to the Arduino Serial Monitor...

Lab EMG - Electromyogram I have result from the lab attached labeled Jennah Introduction Today, we will use the Biopac amplifiers at each station to collect electromyography data, which we will then explore and analyze using Matlab. In this lab, you will investigate the EMG from two muscles resulting from isometric muscle contractions. Matlab code for collecting EMG data (BioPacEMG.m) is posted on Canvas. Verify that your equipment is working correctly before attempting to collect any actual data. Task 1: Data Collection Procedure Before testing your setup, make sure that the power light turns on when you flip the power switch on your amplifier. Dr. Adamovich will explain the proper amplifier settings at the beginning of class. After ensuring the proper locations for electrode placement ...

Project Brief: Kinetic Pulse PCBA 1. Core Functional Requirements Power Input: Must accept AC input from a linear induction coil (approx. 3,000 turns). Energy Storage: Must use a Supercapacitor (1.5F - 2.0F / 5.5V) as the sole energy storage—No chemical batteries. Power Regulation: A boost converter must provide a stable 3.3V rail even as the capacitor discharges down to 0.7V. Power Efficiency: The entire system must be "Nano-power." Total standby/idle current must be < 1µA to ensure the device holds a charge. Timing Logic: An internal timer must trigger a 100ms audible alert (Buzzer) every 40 seconds. Pressure Sensing: The system must interface with a Force Sensitive Resistor (FSR). State 1: Visual Green LED alert when pressure is applied (> 50g). State 2: Visu...