Find Jobs
Hire Freelancers

PCB library in Altium format

$30-250 USD

Në vazhdim
Postuar about 11 years ago

$30-250 USD

Paguhet në dorëzim
There is a schematic based on the Beaglebone design compiled in Altium Designer 10. The schematic is based on a symbol library only and I need a PcbLib library + 3D library for Altium Designer. I have found almost all 3D models in STEP format at http://www.3dcontentcentral.com. Of course I will share all downloaded models. Unfortunately one 3D model (qfn-48 6x6mm) is missing and it requires to be created and added. The list of part numbers that need footprints (please take care of package options which are encoded in part-numbers): Part Number - Manufacturer LQM2HPN2R2MG0L Murata 10106813-071112LF FCI TL5209DR TI TPS65217CRSL TI AM3359ZCZD72 TI MT41K256M16HA-125:E Micron K9F2G08U0C-S Samsung LAN8710A-EZK SMSC APT1608EC Kingbright 7A-24.000MAAE-T TXC 7A-25.000MAHE-T TXC ABS25-32.768KHZ-T Abracon What I give: 1) the symbol library (SchLib) with all components for the project 2) all necessary datasheets that you probably can't find or download, however they all seem to be publicly available 3) all 3D models in STEP format except for the one I can't find What I need: fully assembled library set of symbols+footprints+3D that I can just add to my project and export the schematic to a PCB without any errors! Please take care of the last note. Before you bid please note the following wish/requirement: In fact I'm looking for a contractor with huge background in PCB trace routing who has completed a number of projects with the following list of technologies (not limited to): 1) high speed CPUs - 1GHz and more. This requires good understanding and ability to estimate and simulate heat flows over a PCB. Usually my products are used in industrial applications with temperatures -40 +85 Celsius degrees 2) DDR3 606MHz up to 1066MHz. Real experience is a demand 3) USB 2.0 480Mb 4) Gigabit Ethernet 5) PCIe Gen2 This project is relatively small however a person who wins this project has the potential to have a number of further projects in PCB tracing.
ID e Projektit: 4259851

Rreth projektit

6 propozime
Projekt në distancë
Aktive 11 yrs ago

Po kërkoni të fitoni para?

Përfitimet e ofertës për Freelancer

Vendosni buxhetin dhe afatin tuaj
Paguhuni për punën tuaj
Përshkruani propozimin tuaj
Është falas të regjistrohesh dhe të bësh oferta për punë
I dhënë për:
Avatari i Përdoruesit
hello i can do that thanks
$100 USD në 5 ditë
4,8 (12 përshtypje)
4,5
4,5
6 freelancers are bidding on average $128 USD for this job
Avatari i Përdoruesit
Dear Sir, I can help you on this.
$210 USD në 5 ditë
4,7 (44 përshtypje)
7,5
7,5
Avatari i Përdoruesit
Dear Sir, We are Reserach and Development company whose working area are : -Digital Motor Control -Analog Design -Electronic Design -Power Electronics -PCB design -Embedded system -Matlab -Simulation of hardware For each concept descriptions are as follows: Digital Motor Control: -3-phase induction motor vector control drive -Flux estimation algoritm generation -DSP(TMS320) implementation on motor drive -Low speed application -Torque and speed loop generation -Control algoritms Analog design -Low power distribution -Noissless special opamp based analog circuits -Analog filters -Orcad simulation of several circuits Electronic Design -RF transmitter and receiver -Bluetooh reader and transmitter -Magnetic reader Power Electronics -Implementation motor drive -AC/DC converter -DC-DC converter -Battery charger -Solar inverter -Renewable Energy simulations -Uninterruptle power supplies PCB design -Schematic design by Altium -PCB design by Altium -Power board design -SMPS board design Embedded system -PIC18,PIC24,PIC30 and dsPIC applications -Ardino -MSP430 -Atmel -DSP(Texas Instruments) -Renesas Matlab -Power Electronics simulation -Motor drive -Wind Energy -Solar Energy -Control applications Simulation of Hardware -Orcad Simulation(TI,National, Linear Tech, Maxim libraries) -LTI -National -Matlab Very important Note: References attached. Please look excel file to see projects which we made until now! Metin
$200 USD në 4 ditë
4,7 (9 përshtypje)
4,6
4,6
Avatari i Përdoruesit
Hello, I can do this.
$66 USD në 4 ditë
4,7 (10 përshtypje)
3,3
3,3
Avatari i Përdoruesit
Dear, I can do it. Send me details so that we can start working on it . I assure you good quality work. I am new to this site. But i have last 7 years experience in PCBs designing for Air force. Regards, Syed Ali Nayyar Nasir
$100 USD në 7 ditë
0,0 (0 përshtypje)
0,0
0,0
Avatari i Përdoruesit
We have 20+ Years of experience in PCB design,we have inhouse IPC certified Designer
$100 USD në 3 ditë
0,0 (0 përshtypje)
0,0
0,0

Rreth klientit

Flamuri i RUSSIAN FEDERATION
Lubertsi, Russian Federation
4,5
8
Mënyra e pagesës u verifikua
Anëtar që nga jan 24, 2005

Verifikimi i klientit

Faleminderit! Ne ju kemi dërguar me email një lidhje për të kërkuar kredinë tuaj falas.
Ndodhi një gabim gjatë dërgimit të email-it tuaj. Ju lutemi provoni përsëri.
Përdorues të regjistruar Punë të postuara
Freelancer ® is a registered Trademark of Freelancer Technology Pty Limited (ACN 142 189 759)
Copyright © 2024 Freelancer Technology Pty Limited (ACN 142 189 759)
Po ngarkohet shikimi paraprak
Leja u dha për Geolocation.
Seanca e hyrjes ka skaduar dhe ke dalë. Hyr sërish.