Find Jobs
Hire Freelancers

Analyze RF telegram and build config file for Si446X, CC1120 or similar suitable RF modem

$250-750 USD

Në vazhdim
Postuar over 2 years ago

$250-750 USD

Paguhet në dorëzim
Analyze a RF telegram, determine baud rate, modulation and other config parameters. Make an working configuration file for either SI446X, CC1120 or similar suitable RF modem Info I know of the telegram: There is only preamble, no sync word. I don't need to configure a packet manager, as I want the chip to pass trough sync clock and demodulated signal. I have binary samples of the telegrams captured with hackRF one and dvb-t for you to analyze. Contact for more information and link to binary captures of telegram.
ID e Projektit: 31474001

Rreth projektit

4 propozime
Projekt në distancë
Aktive 3 yrs ago

Po kërkoni të fitoni para?

Përfitimet e ofertës për Freelancer

Vendosni buxhetin dhe afatin tuaj
Paguhuni për punën tuaj
Përshkruani propozimin tuaj
Është falas të regjistrohesh dhe të bësh oferta për punë
I dhënë për:
Avatari i Përdoruesit
$0 USD në 7 ditë
4,8 (5 përshtypje)
4,4
4,4
4 freelancers are bidding on average $500 USD for this job
Avatari i Përdoruesit
Hi! I am an Electronic engineer, PCB Layout, Circuit Design, microcontroller, STM32 microcontroller, C programming expert having past experiences with ,Altium, arduino, pic, AVR, chipkit and Texas instruments microcontrollers I can do this job with 100% satisfaction. Reach me through the chatbox. I am waiting for you over the chat. Thank you!
$750 USD në 12 ditë
4,9 (24 përshtypje)
5,6
5,6
Avatari i Përdoruesit
Hello, thank you for your job posting. I read your description about your project I am a senior electrical engineer. I have plenty of experience in firmware development and micro-controller developments. I can write the firmware based on Arduino, Raspberry Pi, Pic, Atmega, FPGA, ARM, DSP, PLC and so on. And I can design the circuit by the Altium, Eagle, KiCAD, Allegro & OrCAD, PADs. I provide the services - Gerber files, Netlist generation, BOM generation and 3D Models of PCAD and ECAD. I am also good at AutoCAD, Solidworks. And I can simulate all circuits with Proteus, LT-spice, Matlab, Simulink, Multisim, and Labview as well. Due to my experience in firmware development, I will bring you the perfect result in time with high quality. I will also give you a detailed explanation of the process. Looking forward to hearing from you soon Thanks
$500 USD në 7 ditë
5,0 (15 përshtypje)
5,3
5,3

Rreth klientit

Flamuri i NORWAY
Skollenborg, Norway
0,0
0
Mënyra e pagesës u verifikua
Anëtar që nga dhj 22, 2020

Verifikimi i klientit

Faleminderit! Ne ju kemi dërguar me email një lidhje për të kërkuar kredinë tuaj falas.
Ndodhi një gabim gjatë dërgimit të email-it tuaj. Ju lutemi provoni përsëri.
Përdorues të regjistruar Punë të postuara
Freelancer ® is a registered Trademark of Freelancer Technology Pty Limited (ACN 142 189 759)
Copyright © 2024 Freelancer Technology Pty Limited (ACN 142 189 759)
Po ngarkohet shikimi paraprak
Leja u dha për Geolocation.
Seanca e hyrjes ka skaduar dhe ke dalë. Hyr sërish.